How to finish a cross stitch project
Published Updated
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Gear for this job
All 7 picks comparedNurge square plastic embroidery hoops, set of 3
See price on AmazonSee it on AmazonCaydo beech wood embroidery hoops, 7, 8 and 9 in
See price on AmazonSee it on AmazonMufekum Beech Wood Embroidery Hoops, 4-8 in, 5 Pcs
See price on AmazonSee it on Amazon
To finish a cross stitch, secure and trim the thread tails on the back, wash the piece only if it is marked or stained, press it face down on a towel so the stitches stay raised, and then mount it: laced or pinned over board for a frame, gathered into a hoop, or sewn into an ornament, pillow or flatfold. Each step is simple, and doing them in that order prevents the two most common problems, crushed stitches and wrinkles that show under glass.
Step 1: check the stitching and tidy the back
Before anything else, compare the piece to the chart one last time in good light. Look for missed stitches, a backstitch line you forgot, or a half stitch that should be full. It is much easier to fix those now than after the piece is mounted.
Turn the piece over and trim long tails to about a quarter inch. Weave any loose ends under three or four stitches of the same or a darker color first. Dark tails carried across unstitched areas can shadow through to the front, especially on light aida or linen, so trim or reweave those. Remove any gridding thread or basting lines.
Step 2: wash only if it needs it
Washing removes hoop marks, finger oils, pen marks and, on stamped kits, the printed ink. If your piece is clean and was worked on a frame, you can skip it. Stamped kits always need washing to remove the printed pattern, usually a soak in warm water for 20 to 30 minutes.
Use cool to lukewarm water and a mild soap made for delicate fabrics. Soak, swish gently, do not rub, and rinse until the water runs clear. If a red or dark color starts to bleed, keep rinsing in cold water until it stops; do not let the piece sit in still water. Roll it in a clean white towel to remove excess water, never wring it.
Step 3: press face down
Lay a thick, clean white towel on the ironing board and place the stitching face down on it. Press from the back with the iron on a cotton setting, with a pressing cloth if the fabric is delicate, while the piece is still slightly damp. The towel lets the stitches sink in so they are not flattened, and the damp fabric loses its creases.
Press with an up and down motion rather than sliding the iron, which can distort the weave. Leave the piece flat to dry fully before mounting. Make sure the edges and the grain are straight now, because any skew will be locked in once the piece is laced or framed.
Step 4: choose a finish
Framing is the classic finish. The stitching is stretched over acid-free foam board or mat board and held by lacing or pins. For lacing, fold the margins to the back and use strong thread to lace from side to side across the back, then top to bottom, pulling evenly so the grain stays straight. Pinning into the edge of a foam board is quicker and works well for small pieces. If you use glass, a mat or spacers keep it off the stitches.
A hoop finish is quick and popular for small pieces. Center the design in the hoop, tighten, trim the fabric to about an inch outside the hoop, and gather it with a running stitch around the back. Cover the back with a felt or card circle. Ornaments, pillows and flatfolds are sewn finishes: stitching is backed with fabric or felt, stuffed lightly if needed and closed by hand.
Finishing ornaments and small pieces
Small designs make good ornaments, and the simplest finish needs only felt and glue or a few hand stitches. Trim the stitching to the shape you want with half an inch to an inch of margin, fold the margin back or fuse it to a light iron-on interfacing so it will not fray, and glue or whipstitch it to a slightly larger piece of felt. Add a ribbon or cord loop at the top before closing. A thin layer of batting behind the stitching gives a soft, padded look.
For a pillow ornament, place the stitched piece and a backing fabric right sides together, sew around three sides a few squares outside the stitching, turn it right side out, stuff lightly and close the last side by hand. Twisted cord made from leftover floss covers the seam neatly. Plastic canvas ornaments need no backing at all: cut one square outside the stitching and add a hanger.
Margins and sizing for each finish
Leave enough fabric. For framing, 3 inches of margin on each side is the standard so there is room to lace or pin and to adjust the position under the mat. For a hoop finish, the hoop should be at least an inch larger than the design on each side so the design is not crowded against the frame.
Ornaments need only half an inch to an inch of fabric beyond the stitching for seams. Measure your stitched area, add the margin for the finish you have in mind, and buy the frame or hoop to match before you trim anything. Trimming is the only step you cannot undo.
Keeping a finished piece from fading and yellowing
Light is the main cause of fading. Hang framed stitching away from direct sunlight and strong fluorescent light, both of which slowly fade floss colors and can yellow the fabric. Rooms that get afternoon sun on the wall are the riskiest spots. If a piece has to hang in a bright room, UV-filtering glazing reduces the damage but does not stop it, so moving the piece to a shaded wall is still the better fix.
The materials behind the stitching matter as well. Ordinary cardboard and wood-pulp mats are acidic and can leave a brown line or overall yellowing on the fabric after some years, so use acid-free foam board, mat board and backing paper. Store unframed pieces rolled face out around a tube, wrapped in acid-free tissue or a clean cotton cloth, rather than folded or sealed in a plastic bag, which can trap moisture and leave creases.
Frequently asked questions
Do I have to wash cross stitch before framing? No. Wash only if it is marked, stained or from a stamped kit. A clean piece can simply be pressed.
How do I get hoop marks out of aida? Wash it gently in lukewarm water, then press it face down on a towel while still damp.
Should finished cross stitch be framed under glass? Glass protects from dust but should not touch the stitches. Use a mat or spacers, or frame without glass and dust it now and then.
Can I finish cross stitch without sewing? Yes. A hoop finish with a glued felt back, or pinning over foam board in a frame, needs no sewing.
What you need for this
- See price on AmazonAmazon
Nurge square plastic embroidery hoops, set of 3
From Best embroidery hoops for hand embroidery: wood vs plastic
- See price on AmazonAmazon
Fiskars 4 in curved embroidery scissors, stainless
From Best embroidery scissors: small, sharp and curved-tip picks
- See price on AmazonAmazon
Bucilla 84293 Tiny Stocking Cross Stitch Kit
From Best cross stitch ornament kits: Bucilla, Dimensions and Design Works sets
- See price on AmazonAmazon
Q-Snap Needlework Frame Bundle, 3 Sizes
From Best cross stitch frames: Q-Snap frames and scroll frames compared