How to cross stitch on linen

Published

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.

Gear for this job

All 7 picks compared

To cross stitch on linen, you work each X over two fabric threads in each direction instead of over one aida block. That means 28 count linen gives 14 stitches per inch, the same size as 14 count aida, and 32 count gives 16. The extra threads make linen look finer and more traditional, but you count threads rather than holes, so a good light, a consistent starting position and a slightly finer needle make the switch from aida much easier.

Linen count and finished size

Linen is plain-woven, so every thread is separate and you count the threads per inch. Stitched over two, the stitch count is half the thread count: 25 count gives 12.5 stitches per inch, 28 count gives 14, 32 count gives 16, 36 count gives 18 and 40 count gives 20. To size a design, divide its stitch count by the stitches per inch. A design 112 stitches wide is 8 inches on 28 count linen over two.

You can also stitch over one thread on linen for very small details or tiny projects, which doubles the density: 28 count over one is 28 stitches per inch. Most charts are written for over two, and some designers note sections over one on the chart. Real linen has slightly uneven threads (slubs) and that irregularity is part of its look; evenweave fabrics such as Lugana and Jobelan have more uniform threads and are a gentler first step.

Aida and count size chart →

Strands, needles and setup

Use two strands of floss on 25 and 28 count over two, and two strands on 32 count for full coverage or one strand for a lighter, more delicate look. On 36 and 40 count, one strand is usual. Use a blunt tapestry needle, size 26 for 25 to 28 count and 26 or 28 for 32 count and finer.

Prepare the linen before stitching. Zigzag, overlock or tape the edges, since linen frays quickly. Find the center by folding in half both ways and mark it with a short line of basting thread. Many stitchers prefer a Q-Snap or scroll frame for linen, which holds it evenly without the creases a tight hoop can leave on finer fabric. If you use a hoop, remove it between sessions.

Linen comes in many colors, and hand-dyed or mottled linens are popular for samplers and seasonal designs. Check that your floss colors contrast enough with the fabric before you start: a pale floss on a mottled background can disappear in places. Allow at least 3 inches of margin on every side for framing, plus a little extra if you plan to lace the piece over a board.

Q-Snap and scroll frames →

Step by step: the first stitches over two

Thread the needle with an 18 inch length of floss and start with a loop start or a waste knot away from the stitching. Bring the needle up at the bottom left of your first stitch, count two threads to the right and two threads up, and go down there. That is the first leg. Come up two threads below, at the bottom right, and go down two threads up at the top left to complete the X.

The most useful habit is to start each stitch in the same position relative to the weave. In plain weave, vertical threads alternately pass over and under the horizontal ones. Begin your first stitch so that it sits beside a vertical thread that lies on top of a horizontal thread, and every following stitch over two will then land in a matching spot. If you start in mixed positions, stitches can slip under a single thread and look thin or misplaced.

Loop start without knots →

Counting tips and fixing errors

Count threads in pairs, touching each pair with the needle tip as you go. Gridding helps on larger projects: run a line of thin contrasting thread or a removable gridding line every 10 stitches (20 threads) to match the bold lines on the chart. Good daylight lighting and, for 32 count and finer, a magnifier save a lot of recounting.

Check each new section against an already stitched area before continuing. A one-thread error is the most common linen mistake: the stitch looks only slightly off, but the next row will no longer line up. Unpick from the back with the needle tip, or snip a few stitches on the front with fine-point scissors, pull out the cut pieces with tweezers and gently scratch the threads back into line before restitching.

Fixing cross stitch mistakes →

Fractional stitches and travel on the back

Linen makes fractional stitches easier than aida. A quarter or three-quarter stitch goes into the center hole between the two threads of the square, a real hole in the weave rather than a pierce through an aida block. That is one reason designers with lots of fractional stitches recommend linen or evenweave.

Because linen is more open than aida, floss carried across the back can show through on the front, especially dark colors on light fabric. Avoid carrying a thread more than a few stitches across unstitched fabric; end it and restart instead. Keep the back tidy by weaving tails under existing stitches of the same or darker color.

Frequently asked questions

Is cross stitching on linen harder than aida? It takes more care because you count threads, not holes, but the stitch is the same. Starting on 28 count linen or evenweave in good light makes the switch easy.

What count linen is the same as 14 count aida? 28 count linen worked over two threads gives 14 stitches per inch, the same size as 14 count aida.

How many strands do I use on 32 count linen? Two strands for full coverage, or one for a lighter look. Test a few stitches first.

Do I need to wash linen before stitching? Not usually. Most stitchers stitch first and wash the finished piece if needed.

What you need for this