How to make embroidery floss bracelets
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Gear for this job
All 7 picks comparedDMC six-strand floss, 36 popular colors, 8.7 yd
See price on AmazonSee it on AmazonDMC embroidery floss assortment, 100 colors
See price on AmazonSee it on AmazonAnchor stranded cotton floss, 50 skeins, 8 m
See price on AmazonSee it on Amazon
To make an embroidery floss bracelet, cut four to eight full six-strand lengths of floss about 30 inches long, knot them together at one end, tape the knot down, and tie rows of forward or backward knots, each knot made twice, from one side to the other. The candy stripe pattern uses only forward knots and is the best first bracelet; the chevron uses mirrored pairs of colors and both knot directions. Finish by braiding the ends and tying them around the wrist.
What you need
Six-strand embroidery floss in two to six colors, scissors, tape or a clipboard, and a ruler. Use the floss with all six strands together; do not separate it as you would for stitching. Cotton floss knots firmly and holds its shape, while bulk polyester sets are slipperier. A safety pin through the starting knot into a pillow or jeans leg works if you do not have a clipboard.
For a bracelet about 6 to 7 inches long, cut each strand around 30 inches. Knotting uses up length quickly, and the working strand wraps around the others, so short pieces run out before the bracelet is long enough. Wider patterns and thicker bracelets use more.
The four basic knots
Every friendship bracelet pattern is made from four knots, each tied with one working strand around one holding strand. A forward knot: hold the right strand taut, make a 4 shape with the left strand over it, pass the left strand under and up through the loop, and pull up to the top. Repeat the same move a second time. The working strand moves to the right, and the knot shows the working strand's color.
A backward knot is the mirror image: make a reversed 4 with the right strand over the left, pass under and through, pull up, and repeat. The working strand moves to the left. A forward-backward knot is one forward half followed by one backward half, which keeps the working strand where it started; a backward-forward knot is the reverse. These two are used in more complex patterns to change color without moving strands.
Candy stripe bracelet step by step
Cut four colors, two strands each, or simply four to six strands in different colors. Tie them together with an overhand knot about 3 inches from the top and tape the knot to the table. Spread the strands in the order you want the stripes.
Take the leftmost strand and tie a forward knot (twice) onto the second strand, then onto the third, and so on until it reaches the right side. That completes one diagonal row in the first color. Pick up the new leftmost strand and repeat. Keep going until the bracelet is long enough to wrap around the wrist with a small gap. Keep tension even and push each knot right up to the previous one for a tight, regular stripe.
Chevron bracelet step by step
Use four colors, two strands of each, eight strands in all. Arrange them mirrored: A, B, C, D, D, C, B, A. Knot and tape the top. Take the leftmost strand (A) and tie forward knots onto B, C and D, stopping in the middle. Take the rightmost strand (the other A) and tie backward knots onto B, C and D toward the middle.
The two A strands now meet in the center. Tie them together with one forward knot, which joins the two halves of the V. Repeat with the new outer strands (now B), and continue. Each pass makes one V-shaped row of color. If the V tilts, check that you are always knotting the left half with forward knots and the right half with backward knots, and that the center join is tied every row.
Choosing colors is half the fun. Candy stripes look best with high contrast between neighbors, such as a dark, a light and two brights. For gradients, pick four or five shades of one color family from light to dark; floss numbering systems group many shade families, so a set of neighboring shades blends smoothly. Wind leftover lengths onto bobbins and label them, because short pieces are useful for practice and for small charm bracelets.
Finishing and sizing
When the knotted section reaches about an inch shorter than the wrist measurement, stop. Divide the loose ends into two or three groups, braid each for 2 to 3 inches, and knot the end. Undo the starting knot, braid that end the same way, and tie the two braided ends around the wrist with a square knot.
For an adjustable bracelet, lay the two braided ends side by side in opposite directions and tie a sliding knot over both with a separate piece of floss. Trim tails to about half an inch. Cotton floss bracelets can be worn in water, but colors may soften over time; avoid hot water and bleach.
Frequently asked questions
How long should floss be for a friendship bracelet? About 30 inches per strand for a 6 to 7 inch bracelet. Longer for wide patterns, since the working strand wraps around many others.
How many strands do I need for a friendship bracelet? Four to six for a simple candy stripe, eight for a basic chevron. More strands make a wider bracelet.
Do you split embroidery floss for bracelets? No. Use all six strands together as one strand. Splitting makes the bracelet thin and the knots hard to see.
Why does my bracelet curl or twist? Usually tension is uneven or knots are not pushed up tightly. Tape the top down firmly and tie every knot twice with the same pull.
What you need for this
- See price on AmazonAmazon
DMC six-strand floss, 36 popular colors, 8.7 yd
From Best embroidery floss for hand embroidery: brand sets compared
- See price on AmazonAmazon
Fiskars 4 in curved embroidery scissors, stainless
From Best embroidery scissors: small, sharp and curved-tip picks
- See price on AmazonAmazon
Plastic Embroidery Floss Bobbins, White, 360 Pcs
- See price on AmazonAmazon
INFNZOLI Embroidery Floss Organizer, 120 Bobbins