# How to make embroidery floss bracelets

Source: https://hoopandfloss.com/blog/embroidery-floss-bracelets
Published: 2026-10-12
Publisher: Hoop and Floss

To make an embroidery floss bracelet, cut four to eight full six-strand lengths of floss about 30 inches long, knot them together at one end, tape the knot down, and tie rows of forward or backward knots, each knot made twice, from one side to the other. The candy stripe pattern uses only forward knots and is the best first bracelet; the chevron uses mirrored pairs of colors and both knot directions. Finish by braiding the ends and tying them around the wrist.

## What you need

Six-strand embroidery floss in two to six colors, scissors, tape or a clipboard, and a ruler. Use the floss with all six strands together; do not separate it as you would for stitching. Cotton floss knots firmly and holds its shape, while bulk polyester sets are slipperier. A safety pin through the starting knot into a pillow or jeans leg works if you do not have a clipboard.

For a bracelet about 6 to 7 inches long, cut each strand around 30 inches. Knotting uses up length quickly, and the working strand wraps around the others, so short pieces run out before the bracelet is long enough. Wider patterns and thicker bracelets use more.

[Floss sets with many colors](https://hoopandfloss.com/best/best-embroidery-floss)

## The four basic knots

Every friendship bracelet pattern is made from four knots, each tied with one working strand around one holding strand. A forward knot: hold the right strand taut, make a 4 shape with the left strand over it, pass the left strand under and up through the loop, and pull up to the top. Repeat the same move a second time. The working strand moves to the right, and the knot shows the working strand's color.

A backward knot is the mirror image: make a reversed 4 with the right strand over the left, pass under and through, pull up, and repeat. The working strand moves to the left. A forward-backward knot is one forward half followed by one backward half, which keeps the working strand where it started; a backward-forward knot is the reverse. These two are used in more complex patterns to change color without moving strands.

## Candy stripe bracelet step by step

Cut four colors, two strands each, or simply four to six strands in different colors. Tie them together with an overhand knot about 3 inches from the top and tape the knot to the table. Spread the strands in the order you want the stripes.

Take the leftmost strand and tie a forward knot (twice) onto the second strand, then onto the third, and so on until it reaches the right side. That completes one diagonal row in the first color. Pick up the new leftmost strand and repeat. Keep going until the bracelet is long enough to wrap around the wrist with a small gap. Keep tension even and push each knot right up to the previous one for a tight, regular stripe.

## Chevron bracelet step by step

Use four colors, two strands of each, eight strands in all. Arrange them mirrored: A, B, C, D, D, C, B, A. Knot and tape the top. Take the leftmost strand (A) and tie forward knots onto B, C and D, stopping in the middle. Take the rightmost strand (the other A) and tie backward knots onto B, C and D toward the middle.

The two A strands now meet in the center. Tie them together with one forward knot, which joins the two halves of the V. Repeat with the new outer strands (now B), and continue. Each pass makes one V-shaped row of color. If the V tilts, check that you are always knotting the left half with forward knots and the right half with backward knots, and that the center join is tied every row.

Choosing colors is half the fun. Candy stripes look best with high contrast between neighbors, such as a dark, a light and two brights. For gradients, pick four or five shades of one color family from light to dark; floss numbering systems group many shade families, so a set of neighboring shades blends smoothly. Wind leftover lengths onto bobbins and label them, because short pieces are useful for practice and for small charm bracelets.

[Bobbins to keep strands untangled](https://hoopandfloss.com/best/best-floss-bobbin-winder)

## Finishing and sizing

When the knotted section reaches about an inch shorter than the wrist measurement, stop. Divide the loose ends into two or three groups, braid each for 2 to 3 inches, and knot the end. Undo the starting knot, braid that end the same way, and tie the two braided ends around the wrist with a square knot.

For an adjustable bracelet, lay the two braided ends side by side in opposite directions and tie a sliding knot over both with a separate piece of floss. Trim tails to about half an inch. Cotton floss bracelets can be worn in water, but colors may soften over time; avoid hot water and bleach.

[Small sharp scissors for trimming](https://hoopandfloss.com/best/best-embroidery-scissors)

## Frequently asked questions

How long should floss be for a friendship bracelet? About 30 inches per strand for a 6 to 7 inch bracelet. Longer for wide patterns, since the working strand wraps around many others.

How many strands do I need for a friendship bracelet? Four to six for a simple candy stripe, eight for a basic chevron. More strands make a wider bracelet.

Do you split embroidery floss for bracelets? No. Use all six strands together as one strand. Splitting makes the bracelet thin and the knots hard to see.

Why does my bracelet curl or twist? Usually tension is uneven or knots are not pushed up tightly. Tape the top down firmly and tie every knot twice with the same pull.

## Gear guides for this topic

- https://hoopandfloss.com/best/best-embroidery-floss
- https://hoopandfloss.com/best/best-embroidery-scissors
- https://hoopandfloss.com/best/best-floss-bobbin-winder
- https://hoopandfloss.com/best/best-embroidery-floss-organizer
